Discussion Forums

Hi Gary, only just saw this sorry. The deer would need to be very large, in excess of 200lb to ensure that this particular bullet meets some resistance. This is a less than ideal situation because the velocity / energy is low and chances are game resistance is not high either. The bullet may mushroom but the wound may be no more than a half inch in diameter with some bruising around it. Best results will occur if you drive into major bones. So if possible, keep your shots well forwards. The KB h..

I've been shooting since I was 4 years old and hunting since I was 6, and I am 43 now. Started learning to reload with my dad when I was 10 and really though I was pretty knowledgeable till I started reading your website, the knowledge base and the threads. By reading your studies I realized why I did some of the thinks I did when reloading, setting up a rifle, load development, etc, thinks I learned from my dad and I never questioned them but now I know why I agree with you on not trusting the ..

So I started this thread about a year and a half ago, when after reading Nathan's medium bore cartridge write ups way, way too many times i found myself bitten by the medium bore bug and just had to get one. I went back and forth on a bunch of different options with a 9.3x62, the Ruger Guide gun 375 and 338 Win mag being the top contenders... But sometimes a good deal is what is needed to break the dead lock so I just ended up the proud new owner of a Weatherby MK V Lefthanded in 340 Weatherby !..

You can try out Hammer Bullets, I dont know if they ship outside the US but you can check. You'll want a light for caliber bullet so you can push it faster, however these bullets are guaranteed to provide terminal peeformance down to 1,800 fps. Of course higher impact velocities are recommended, but they work great. Here is a link to some more info on them: https://www.longrangehunting.com/threads/hammer-bullets.211476/ Best regards, Luis

Some updates for everyone who’s been wondering how the project has been coming along: - The rifle is fully assembled and ready to shoot. Everything has been threadlocked and torqued to either manufacturer’s specs or Nathan’s specs in the case of the action screws. A quick summary of what I’ve done to a stock SPS 7mm Rem Mag circa 2008 manufacture: - Stocky’s M50 Laminate w/aluminum block stock, middle swivel stud removed - TriggerTech Primary trigger set as low as it goes (1.5 to 2 pounds) - War..

don't wanna hijack this thread, but since i have posted in it before i'll do so again. got to FINALLY take my rem 700 5r 20" bbl bottom metal 308 (i glass bedded the recoil lug with devcon) to the range today. using some of my run of the mill reloads i also shoot in an M1A ( 168 gr sierra HPBT over 42.5 REL15 in LC military cases). i say run of the mill as they weren't checked for concentricity etc. they WERE loaded on my forester co-ax. i messed around at 50 yds getting it on paper etc then at ..

Quote:Some of you may be missing the point here. I was talking about recent batch issues. Lately I have been seeing issues with bullets weighing less than 100 grains at impact velocities over 2900fps in flesh, recovered bullets showing zero expansion. I suggested folk keep an eye on (test) their current ammo just to be sure. This has nothing to do with game shot in the past and comments of this nature have no relevance to this discussion. When/where did you wrote that... not in this thread...? I..

It looks as if the holes had some contaminant in them. The threads are still intact, but you can see how the apex has been rounded off. As Nathan said, you should find a hand tap and t-handle and clean up the threads in the hole first. If you try to wind in the new bolts, the same thing will happen again. Be very careful about your alignment when using the tap, not difficult to do, but can sometimes be tricky to get it started. The issue being where the threads of the hole are damaged. A taper t..

Hi Bryan, the common name for this thread pitch is 1/4" UNF (1/4" x 28). If there has been some cross threading (perhaps compound seeped into the threads), it may pay to obtain a thread tap and wind this in by hand to clean up the threads. If you need new screws, these will ship from the U.S (Midway / Brownells) to Ireland without restrictions. But you may also be able to find 1/4" UNF hex heads locally.

Remington should (may) have 1/4-28 screws. Without a better picture, it looks like this one was cross-threaded or had something in the hole. May also have been screwed into a differently threaded hole, perhaps a 1/4-20 or 1/4-32?

Just thought id share this interesting thread. https://www.facebook.com/703367527/posts/10157087448592528?sfns=mo

John, here are instructions for posting photos in this forum: https://www.ballisticstudies.com/Resources/Discussion+Forums/x_forum/29/thread/1586.html [https://www.ballisticstudies.com/Resources/Discussion+Forums/x_forum/29/thread/1586.html] Love to see this oddity.