@ 04:47 am (GMT) |
Robert McLeanI am wondering if anyone has had any experience with the Browning BXR or BXC ammo for 7mm Rem Mag. |
@ 07:38 am (GMT) |
Nathan FosterRe: Browning BXR an BXC AmmoHi Robert, I have some experience and am receiving ongoing input from readers using it in the field.The bonded bullet is much the same as the Interbond, the hollow point helps somewhat to initiate expansion. The non bonded bullet is very fast expanding, good for lean animals in open country. Neither have sizzling BC's but both have their uses and its good to see Browning offering different loads to suit different game / situations. |
@ 10:07 am (GMT) |
Robert McLeanRe: Browning BXR an BXC AmmoThanks Nathan. There is a rebate and I thought I would take advantage to put more rounds through the Tikka 7mm Rem Mag. Factory ammo is ridiculous $$ for the 7mm.I need the practice, not getting great groups and I think it is technique because there is nothing consistent. Just waving the thing around and then yanking on it. Using that Winchester 7mm 150 super-x you used so I am really confused as to why I am not getting those sub moa groups you did in the video after a hand full of shots. Actually I am not confused at all... I read some reviews on Browning BXC ammo at a sporting store site where some people were complaining about the quality. Loose bullets, burrs, loose tips. |
@ 10:29 am (GMT) |
Nathan FosterRe: Browning BXR an BXC AmmoThat is a good point that the guys have made. Concentricity is a major concern at present. That ammo I used in the vid was ok, but not great. The most recent stuff is quite poor from Win and will be the same for Browning.This new issue keeps catching me out. I am seeing it a lot lately but sometimes neglect to mention it because the guys want to know about the terminal performance and unless we are talking about accuracy or long range work, my focus is directed to the bullet construction. I have to keep reminding myself of this. At my last club lecture, I took a concentricity gauge and some factory ammo, handed it around, shocked everyone. ' Over the coming months, we are going to have to remind each other of this current issue as ammo makers struggle to keep up with demand. If in doubt, sort your factory ammo using a concentricity gauge. And yes, this sounds a bit OCD but its notbased on the current situation and if you have a con gauge before you start reloading, you will have the best possible start. As for factory ammo Robert, have a look at Federal. But if you want brass, look at the more basic loads from Hornady. Note also, the Tikkas tend to like the 154 and 162gr Hornady loads over the 140gr. And yes, that rifle is a handful, a real animal. Your forehand fingers should be sore after shooting. Should feel quite sore the next day but hopefully nothing in the shoulder. keep at it. |
@ 09:09 pm (GMT) |
Ben LawRe: Browning BXR an BXC AmmoI checked some factory ammo a few years back that wasn't shooting the best, concentricity measured 17 thou runout. |
@ 04:00 am (GMT) |
Robert McLeanRe: Browning BXR an BXC AmmoNothing in the shoulder but obviously not holding that forend hard enough.Those Browning rounds have nickel plated shell casings. Can they be used reliably for reloading? |
@ 07:26 am (GMT) |
Nathan FosterRe: Browning BXR an BXC AmmoHi Ben, yes 17 thou is bad. In situations like that, I wish I could go the the gun and ammo makers with an SKS and surplus ammo and say "look guys, this effing beat up SKS and its ammo is more accurate and unfortunately more ethical, even with FMJ ammo, than the shit you are trying to push on our shooters. Stop pissing around with your fancy websites and promo videos and get your effin acts together".Robert, I would assume that the brass is Olin. I love Win Brass, its strong and of a good capacity. But some of the latest stuff has thickness issues. Even if the necks are turned, the cases still bow after firing due to the thickness in the body. Nickel plating can make this more pronounced and also make neck turning impossible if we are only taking 50%. Its really hard for me to say what to expect. I am still using Win brass, but I am batching it. A lot has to be chucked at the moment in certain calibers. In other calibers, its fine. Again, having a gauge is the key, can check the run out on fired brass. I am finding the current brass from Hornady to be very good. So even if the factory ammo is a bit off as it has sometimes been in the most popular cals, the brass is good. Again, keep an eye out for any deals on Hornady, especially the 154gr ammo with regards to your rifle. But do keep in mind that the SF loads are at full hand load speeds and so again- tight grip and white finger pads. |